[Musix-Help] el problema de lilo

Jue Ago 18 23:36:33 CEST 2005

lilo musix en hda3

# /etc/lilo.conf - See: 'lilo(8)' and 'lilo.conf(5)',
# ---------------       'install-mbr(8)', '/usr/share/doc/lilo/',
#                       and '/usr/share/doc/mbr/'.

# +---------------------------------------------------------------+
# |                        !! Reminder !!                         |
# |                                                               |
# | Don't forget to run 'lilo' after you make changes to this     |
# | conffile, '/boot/bootmess.txt', or install a new kernel.  The |
# | computer will most likely fail to boot if a kernel-image      |
# | post-install script or you don't remember to run 'lilo'.      |
# |                                                               |
# +---------------------------------------------------------------+

# Support LBA for large hard disks.
#
lba32

# Defines boot-time changes to partition type numbers
change-rules
   reset

# Overrides the default mapping between harddisk names and the BIOS'
# harddisk order. Use with caution.
#disk=/dev/hde
#    bios=0x81

#disk=/dev/sda
#    bios=0x80

# Specifies the boot device.  This is where Lilo installs its boot
# block.  It can be either a partition, or the raw device, in which
# case it installs in the MBR, and will overwrite the current MBR.
#
boot=/dev/hda

# Specifies the device that should be mounted as root. ('/')
#
root=/dev/hda3

# Enable map compaction:
# Tries to merge read requests for adjacent sectors into a single
# read request. This drastically reduces load time and keeps the
# map smaller.  Using 'compact' is especially recommended when
# booting from a floppy disk.  It is disabled here by default
# because it doesn't always work.
#
# compact

# Default menu for Debian. (Using the images from debian-bootscreen)
# from Philipp Wolfer <phil en newswriter.org>.
bitmap=/boot/debian.bmp
bmp-colors=1,,0,2,,0
bmp-table=120p,173p,1,15,17
bmp-timer=254p,432p,1,0,0

# Install the specified file as the new boot sector.
# LILO supports built in boot sectory, you only need
# to specify the type, choose one from 'text', 'menu' or 'bitmap'.
# new: install=bmp      old: install=/boot/boot-bmp.b
# new: install=text     old: install=/boot/boot-text.b
# new: install=menu     old: install=/boot/boot-menu.b or boot.b
# default: 'menu' is default, unless you have a bitmap= line
# Note: install=bmp must be used to see the bitmap menu.
# install=menu
# install=bmp
install=bmp

# Specifies the number of _tenths_ of a second LILO should
# wait before booting the first image.  LILO
# doesn't wait if DELAY is omitted or if DELAY is set to zero.

delay=20

# Prompt to use certaing image. If prompt is specified without timeout,
# boot will not take place unless you hit RETURN
prompt
timeout=50

# Specifies the location of the map file. If MAP is
# omitted, a file /boot/map is used.
map=/boot/map

# Specifies the VGA text mode that should be selected when
# booting. The following values are recognized (case is ignored):
#   NORMAL  select normal 80x25 text mode.
#   EXTENDED  select 80x50 text mode. The word EXTENDED can be
#     abbreviated to EXT.
#   ASK  stop and ask for user input (at boot time).
#   <number>  use the corresponding text mode. A list of available modes
#     can be obtained by booting with  vga=ask  and pressing [Enter].
vga=791

# You can set a password here, and uncomment the 'restricted' lines
# in the image definitions below to make it so that a password must
# be typed to boot anything but a default configuration.  If a
# command line is given, other than one specified by an 'append'
# statement in 'lilo.conf', the password will be required, but a
# standard default boot will not require one.
#
# This will, for instance, prevent anyone with access to the
# console from booting with something like 'Linux init=/bin/sh',
# and thus becoming 'root' without proper authorization.
#
# Note that if you really need this type of security, you will
# likely also want to use 'install-mbr' to reconfigure the MBR
# program, as well as set up your BIOS to disallow booting from
# removable disk or CD-ROM, then put a password on getting into the
# BIOS configuration as well.  Please RTFM 'install-mbr(8)'.
#
# password=tatercounter2000

# You can put a customized boot message up if you like.  If you use
# 'prompt', and this computer may need to reboot unattended, you
# must specify a 'timeout', or it will sit there forever waiting
# for a keypress.  'single-key' goes with the 'alias' lines in the
# 'image' configurations below.  eg: You can press '1' to boot
# 'Linux', '2' to boot 'LinuxOLD', if you uncomment the 'alias'.
#
# message=/boot/bootmess.txt
#	prompt
#	single-key
#	delay=100
#	timeout=100

# Kernel command line options that apply to all installed images go
# here.  See: The 'boot-prompt-HOWO' and 'kernel-parameters.txt' in
# the Linux kernel 'Documentation' directory.
#
# append=""
# Boot up Linux by default.
#
default="Linux"

image=/boot/vmlinuz
	label="Linux"
	initrd=/boot/initrd.img
	append="ramdisk_size=100000 init=/etc/init lang=es apm=power-off nomce"
	read-only
image=/boot/vmlinuz-2.6.11
	label="Linux(2.6)-1"
	initrd=/boot/initrd.img-2.6.11
	append="ramdisk_size=100000 init=/etc/init lang=es apm=power-off nomce"
	read-only

image=/boot/vmlinuz-2.6.11-1-386
	label="Linux(2.6)-2"
	initrd=/boot/initrd.img-2.6.11-1-386
	append="ramdisk_size=100000 init=/etc/init lang=es apm=power-off nomce"
	read-only

# If you have another OS on this machine to boot, you can uncomment the
# following lines, changing the device name on the 'other' line to
# where your other OS' partition is.
#
# other=/dev/hda4
#	label=HURD
#	restricted
#	alias=3
other=/dev/hda1
	label="Windows(hda1)"
other=/dev/hdb1
	label="Windows(hdb1)"